Air 403 Wind Generator Tower Kits

The Tower Kit

27 foot kit: $139.00

45 foot kit: $199.00

(kits do not include poles or anchors)

Anchors

36" (for 27 foot kit) set of 4 $55.00

48" (for 45 foot kit) set of 4 $70.00

The Roof Mount Kit: $79.00

with Roof Seal: $99.00

Available in 27 and 45 foot kits

Installs in a few hours No Cement

No Gin Pole
(27' only)

No Winching

No Sweat!

Includes everything except pipe and anchors

45' Tower Kit includes gin pole hardware

How easy is it to install?

Technical Information 45'
Technical Information 27'

No Room for
a tower...

Simple roof top tower mount offers easy installation for your AIR wind module

Design includes vibration isolation mounts that reduce mechanically transmitted noise by 80%

Installs on the side of a building or through the roof

Includes everything except pole and mounting bolts

How easy is it to install?

Technical Information

airroof.jpg (4921 bytes)

45' Guyed Tower Kit
Technical Information

A Revolution in Tower Design

Kits include:

Base Connector

Upper Wire Set (280 ft. pre-cut)

Lower Wire Set (160 ft. pre-cut)

Base Staples

3/8" x 1 ½" Bolt

3/8" Locknut

Cable Thimbles

Cable Clamps

Set Up Kit

45 ft (14 m)

* Note: This 45 foot Tower Kit includes a setup kit to raise the tower.
If more than one tower is to be erected, a single setup up kit
can be used for any towers to be installed. See below for kit details.

Setup Kit

Kits include:

Gin Pole Cap

100 Foot Rope

Snap Links

8 Foot Cable

3/8" x 1-1/2" Bolt

3/8" Locknut

Quantity)

Pipe Pieces Needed:
(available at fence suppliers)

24 foot (7.2 meter) length for tower
21 foot (6.3 meter) length for tower
6 foot (1.8 meter) length for tower base
21 foot (6.3 meter) length for gin pole

Pipe Requirements

Tower Kits use 1-7/8 inch (47.5 mm) Steel Tubing

Maximum Wind Speed

Maximum
Wind Speed

70 mph

80 mph

90 mph

Recommended
Wall Thickness

.065 inch (1.65 mm)

.090 inch (2.3 mm)

.140 inch (3.6 mm)

Pipe
Schedule

n/a

Schedule 20

Schedule 40

27' Guyed Tower Kit
Technical Information

A Revolution in Tower Design

Kits include:

Base Connector

Lower Wire Set (160 ft. pre-cut)

Base Staples

3/8" x 1 ½" Bolt

3/8" Locknut

Cable Thimbles

Cable Clamps

27 ft (8 m)

Pipe Pieces Needed:
(available at fence suppliers)

24 foot (7.2 meter) length for tower
3 foot (.9 meter) length for tower
6 foot (1.8 meter) length for tower base

Pipe Requirements

Tower Kits use 1-7/8 inch (47.5 mm) Steel Tubing

Maximum Wind Speed

Maximum
Wind Speed

90 mph

100 mph

120 mph

Recommended
Wall Thickness

.065 inch (1.65 mm)

.090 inch (2.3 mm)

.140 inch (3.6 mm)

Pipe
Schedule

n/a

Schedule 20

Schedule 40

Kits include:

Isolators

Base Plates

Clamp Sleeves

Clamp Straps

5/16' x 1? Bolts

5/16' Lock Washers

Safety Leashes

Optional Roof Seal

Quantity

4

2

2

2

4

4

2

(1)